Mauser K98K Ultra low-profile NDT Scout Mount for Long Eye Relief Scopes Mauser K98K Ultra low-profile NDT Scout Mount for Long Eye Relief Scopes BadAce Tactical [Firearms, optics, and rings are for display only and NOT included] NOTE: Works for Mauser Karabiner 98 kurz (Carbine 98 Short, often abbreviated as Kar98k, K98, or K98k). Does NOT work for K98A or K98AZ (pre-Kar98k) or ANY other Mausers No drill, no tap, no permanent modification to your Mauser K98K ULTRA low profile design allows comfortable cheek weld - lowest 98K scope mount on the market Works with Long Eye Relief (LER) scopes and you can still use stripper clips for speed loading No gunsmith required, installed in 20 minutes! Precision CNC milled from a whole block of aircraft grade aluminum alloy HOW TO IDENTIFY YOUR RIFLE (NOT all Mausers are K98k): Mauser K98k has a short handguard that is approximately 7 inches long and is in front of the rear sight. The rear sight base is 3.5 inches long.  We strongly encourage you to remove the rear sight leaf following this illustration image or the YouTube installation video above to confirm that your rifle is indeed a K98k before placing your order. If you are not sure what your rifle is please check this FAQs page first. You can also contact us for future help.  NOTE:  How to remove the rear sight retaining pin Not all rifles' rear sight leaves have retaining pins. You should be able to see the retaining pin sticking out a little bit from the head of the rear sight leaf if there is one, such as this one:  The retaining pin is slightly longer than the rear sight leaf - this is to prevent it from being pressed down and removed. So, if your rear sight leaf has a retaining pin present, you must punch it out first.  Some models don't have retaining pins, such as this one below:  If that is the case, you can simply press down the rear sight leaf and remove it.  The easy way to remove the rear sight leaf:  The following are links to the equipment we used in this video including the scope mount and other third-party accessories such as rings, scopes, etc. We purchased these accessories by ourselves, and we only recommend products that we trust and have been tested extensively by us. LONG EYE RELIEF SCOPES: Hi-Lux Optics Long Eye Relief 2-7x32mm Riflescope (used in this video)We also recommend the Burris scout riflescope 2-7x32mm, which comes with the Burris forever warranty SCOPE RINGS: Both two LER scopes above have a 32mm objective lens and can be mounted very close to the bore, which is always desired by shooters. The following two low-profile scope rings are the perfect match for this setup at competitive prices: Weaver Quad Lock 1-Inch medium 49046 (used in this video) Leupold Rifleman Detachable low Rings 56524 Videos How to remove the rear sight leaf: How to install the NDT K98k scout mount:

Mauser K98K Ultra low-profile NDT Scout Mount for Long Eye Relief Scopes

Add Your Review
$69.95 USD
In Stock
Add to Wishlist
[Firearms, optics, and rings are for display only and NOT included]

NOTE: Works for Mauser Karabiner 98 kurz (Carbine 98 Short, often abbreviated as Kar98k, K98, or K98k). Does NOT work for K98A or K98AZ (pre-Kar98k) or ANY other Mausers

  • No drill, no tap, no permanent modification to your Mauser K98K
  • ULTRA low profile design allows comfortable cheek weld - lowest 98K scope mount on the market
  • Works with Long Eye Relief (LER) scopes and you can still use stripper clips for speed loading
  • No gunsmith required, installed in 20 minutes!
  • Precision CNC milled from a whole block of aircraft grade aluminum alloy

HOW TO IDENTIFY YOUR RIFLE (NOT all Mausers are K98k):

Mauser K98k has a short handguard that is approximately 7 inches long and is in front of the rear sight. The rear sight base is 3.5 inches long. 

We strongly encourage you to remove the rear sight leaf following this illustration image or the YouTube installation video above to confirm that your rifle is indeed a K98k before placing your order. If you are not sure what your rifle is please check this FAQs page first. You can also contact us for future help. 


NOTE:  How to remove the rear sight retaining pin

Not all rifles' rear sight leaves have retaining pins. You should be able to see the retaining pin sticking out a little bit from the head of the rear sight leaf if there is one, such as this one: 

The retaining pin is slightly longer than the rear sight leaf - this is to prevent it from being pressed down and removed. So, if your rear sight leaf has a retaining pin present, you must punch it out first. 

Some models don't have retaining pins, such as this one below: 

If that is the case, you can simply press down the rear sight leaf and remove it. 


The easy way to remove the rear sight leaf: 


The following are links to the equipment we used in this video including the scope mount and other third-party accessories such as rings, scopes, etc.

We purchased these accessories by ourselves, and we only recommend products that we trust and have been tested extensively by us.

[Firearms, optics, and rings are for display only and NOT included]

NOTE: Works for Mauser Karabiner 98 kurz (Carbine 98 Short, often abbreviated as Kar98k, K98, or K98k). Does NOT work for K98A or K98AZ (pre-Kar98k) or ANY other Mausers

  • No drill, no tap, no permanent modification to your Mauser K98K
  • ULTRA low profile design allows comfortable cheek weld - lowest 98K scope mount on the market
  • Works with Long Eye Relief (LER) scopes and you can still use stripper clips for speed loading
  • No gunsmith required, installed in 20 minutes!
  • Precision CNC milled from a whole block of aircraft grade aluminum alloy

HOW TO IDENTIFY YOUR RIFLE (NOT all Mausers are K98k):

Mauser K98k has a short handguard that is approximately 7 inches long and is in front of the rear sight. The rear sight base is 3.5 inches long. 

We strongly encourage you to remove the rear sight leaf following this illustration image or the YouTube installation video above to confirm that your rifle is indeed a K98k before placing your order. If you are not sure what your rifle is please check this FAQs page first. You can also contact us for future help. 


NOTE:  How to remove the rear sight retaining pin

Not all rifles' rear sight leaves have retaining pins. You should be able to see the retaining pin sticking out a little bit from the head of the rear sight leaf if there is one, such as this one: 

The retaining pin is slightly longer than the rear sight leaf - this is to prevent it from being pressed down and removed. So, if your rear sight leaf has a retaining pin present, you must punch it out first. 

Some models don't have retaining pins, such as this one below: 

If that is the case, you can simply press down the rear sight leaf and remove it. 


The easy way to remove the rear sight leaf: 


The following are links to the equipment we used in this video including the scope mount and other third-party accessories such as rings, scopes, etc.

We purchased these accessories by ourselves, and we only recommend products that we trust and have been tested extensively by us.

How to remove the rear sight leaf:



How to install the NDT K98k scout mount:

PLEASE READ THE FOLLOWING TERMS AND CONDITIONS OF USE CAREFULLY BEFORE USING THIS WEBSITE. All users of this site agree that access to and use of this site are subject to the following terms and conditions and other applicable law. If you do not agree to these terms and conditions, please do not use this site.

Order Processing:

Normal order processing can take between 1-3 business days (Monday – Friday)

Return Policy:

We guarantee the quality of our products and we want you to be completely satisfied with your purchases. If for any reason you are not completely satisfied with your purchase, you can return the purchased items within 30 days of receipts for an exchange or full refund/Credit (less shipping charges). If you would like to make a return or exchange, you must contact us by email to get an RMA (Return Merchandise Authorization) number before returning your items.

Please note that shipping cost is non-refundable, and we are not responsible for the return shipping.

Orders returned after 30 days will be subject to a 25% re-stocking fee. Orders returned after 90 days will be subject to a 50% re-stocking fee.

Limited Lifetime Warranty

We (Ace Recreational Equipment and Services Limited) warrants our NDT Scope Mount to be free of defects in materials and workmanship for as long as it is owned by the original owner. We will repair or replace (at our option) any such defective product when it is returned by the original owner with a copy of the original receipt. The repair or replacement will be without charge except for reasonable shipping, handling and insurance charges.

International (outside of Canada and USA) Ordering

  • International orders are shipped via CanadaPost. There is no delivery guarantee on international orders.  We have no control over customs, international taxes, or other charges imposed by countries outside of the US and Canada.
  • We (Ace Recreational Equipment and Services Limited) are NOT responsible for international shipping delays, such as customs delays and are not responsible for any customs. The buyer assumes all responsibilities of claims made with the shipping carrier and all duties/fees incurred on the shipment. Please contact info@badacetactical.com if you have any questions.
  • Leaving a valid phone number is highly recommended in case the customs office of your country needs to contact you for importing fees or taxes. 
  • All international packages must include a customs form with values of the products. Please do NOT ask us to remove the value or claim it as a gift. Without the customs form, the postal office / customs office will reject the package.